主要パラメータ
Main Optoelectronic Indicators
1. Linear mode parameters
Parameters | Test conditions（unless otherwise specified，TC =25±5℃) | Min | Max | Unit |
Effective detection surface diameterd | — | 25 | — | μm |
Spectral response range | — | 950 | 1650 | nm |
Reverse breakdown voltage VBR | IR=10 μA ，Φe=0 | 60 | 85 | V |
Responsivity Re | Φe=1μW，VR=(VBR-1)V, λ=1550 nm±50 nm | 8 |
| A/W |
Dark current ID | VDC =(VBR-1) V，Φe=0 |
| 1 | nA |
Capacitance Ctot | VDC =(VBR-1) V，f=1MHz | — | 0.6 | pF |
Breakdown voltage temperature coefficient η | TC =-45～+30℃ , IR =10μA，φe=0 | 0.10 | 0.15 | V/℃ |
2. Geiger Mode Parameters
Parameters | Test Conditions | Min | Max | Unit |
Single photon detection efficiency PDE | TA = -40±5℃, μ=1 ，fg = 100 MHz ，fP = 500 kHz ，DCR ≤ 3.0 kcps ，λ = 1.55μm | 20 |
| % |
Dark count rate DCR | TA = -40±5℃, fg = 1.25 GHz， SPDE ≥ 20% ，λ = 1.55μm |
| 3 | kcps |
After pulse probability APP (1000 ns) | TA = -40±5℃, μ=1 ，fg = 1.25 GHz ，fP = 625kHz ，DCR ≤ 3.0 kHz ，SPDE ≥ 20% ，λ = 1.55μm |
| 1
| % |
Time jitter TJ | SPDE=20% |
| 300 | ps |
Note: λ is the wavelength of incident light, fp is the frequency of the optical pulse signal, and R is the sampling resistor.
Absolute Maximum Ratings and Recommended Operating Conditions
Item | Parameter | Rating |
Absolute Maximum Ratings | 1 | Storage temperatureTSTG | -50℃~+85℃ |
| 2 | Operating environment temperatureTC | -50℃~60℃ |
| 3 | Soldering temperatureTsld（time） | 260℃（10s） |
| 4 | Reverse DC bias voltage VDC | VBR+5 V |
| 5 | Input optical powerφe（continuous） | 1 mW |
| 6 | Forward currentIF（continuous） | 200 μA |
| 7 | Electrostatic discharge sensitivityESD | ≥300 V |
| 8 | Pigtail pulling force | 3.0 N |
| 9 | TEC voltage | 11.9 V |
| 10 | TEC current | 0.8 A |
Item | Parameter | Rating |
|
Recommended Operating Conditions | 1 | APD chip operating temperatureTth | -50℃~-30℃ |
|
| 2 | Reverse DC bias voltageVDC | VBR+1V～VBR+5V |
|
Typical characteristic curve
Figure 1 Photocurrent and dark current curves
Figure 2 Breakdown voltage temperature coefficient
寸法およびピン定義
Package Outline
Dimensions
Symbol | Min |
| Max | Symbol | Min |
| Max | Symbol | Min |
| Max |
H1 | 7.40 | 7.45 | 7.50 | L2 | 10.00 | 13.50 | 30.00 | L8 | 8.70 | 8.90 | 9.10 |
H2 | 1.80 | 2.00 | 2.20 | L3 | 4.05 | 4.25 | 4.45 | L9 | 12.50 | 12.70 | 12.90 |
H3 | 7.57 | 7.77 | 7.97 | L4 | 3.74 | 3.94 | 4.14 | L10 | 38.20 | 38.40 | 38.60 |
H4 | 10.50 | 10.70 | 10.90 | L5 | 21.80 | 22.00 | 22.20 | ф 1 | 3.00 | 3.50 | 6.60 |
L0 | 1000.0 | - | - | L6 | 25.80 | 26.00 | 26.20 | ф2 | 0.40 | 0.50 | 0.60 |
L1 | 17.30 | 17.50 | 17.70 | L7 | - | 2.54 | - | ф3 | 2.20 | 2.40 | 2.60 |
Equivalent Circuit and Pin Definitions
Pin# | Function | Pin# | Function |
1 | Diode N (APD_N) | 5 | TEC- |
2 | Case Ground (GND) | 6 | Thermistor (R_th ) |
3 | Diode P (APD_P) | 7 | Thermistor (R_th ) |
4 | Signal sampling terminal P+50Ω (OUT) | 8 | TEC+ |
TEC\NTC Electrical parameters
NTC (Thermistor): RT=10 kΩ @ 25℃, β=3450,5%.
TEC (Thermoelectric Cooler): IMAX=0.8 A, VMAX=11.9 V, THMAX=200℃
注文情報
SPD6528Q-XX-XX/XXX(XXX)
XX:Fiber Type
SM
MM(62.5)
MM(50)
XX/XXX:Fiber Connector
XX: FC
SC
LC
NC
XXX:UPC
APC
(XXX):Fiber Length
1.0m
1.5m
Note:
● The product is an electrostatic sensitive device, and ESD protection must be taken during storage and use.
● The bending radius of the product fiber is not less than 30mm. Avoid fiber breakage and contamination or damage to the connector during storage and use.
● The product requires external refrigeration. The clamping carrier used for refrigeration needs to be made of a material with good thermal conductivity, keep the cavity wall at one end of the device lead and the contact surface of the clamping carrier tightly matched, and apply thermal conductive material on the contact surface of the two.
● The product should be stored in a clean environment with ventilation and no corrosive gas at a temperature of -10~+40℃ and a relative humidity of no more than 80%.
