Based on state-ofart Lithium Niobate on insulator (LNOl) technology, this intensity modulator inheritsmost of the advantages of traditional lithium niobate modulators, and has a miniature form factor, lowdriving voltage and low loss.
LP-MZM-T-BW is the thermal tuning version, whose phase shit is tuned by micron heaters integratedon chip. Compared to traditional LN modulators, the heater version could maintain a lot more stable biaspoint throughout lifetime of the device. The device is a hermetic sealing package with internal opticalpower, which save more space size for the end user.
The low RlN laser source is also integrated in the package. Two PD's are included for power monitoringpurpose. One PD is used to monitor the laser output power and the other is to monitor the MZ bias point.
Electrical Characteristics
ORI-MZM-T-BW
No. | Parameter | Symbol | Min | Typ | Max | Unit |
1 | RF Vπ @ 1kHz | Vpi_RF | - | 3.3 | 3.5 | V |
2 | RF Vπ @ 1GHz | Vpi_RF | - | - | 4 | V |
3 | Electro-optical 3-dB Bandwidth* | BW | 20/40 | - | - | GHz |
4 | Electrical return loss (f<40GHz) | S11 | - | - | -10 | dB |
5 | Characteristic impedance | Zc | - | 50 | - | Ohm |
6 | Heater resistance | Rhtr | 160 | - | 260 | Ohm |
7 | DC tuning Pπ | Pπ_DC | 45 | 55 | 70 | mW |
8 | LD operating current | If | - | 300 | 400 | mA |
9 | LD Forward Voltage | Vr | 1.2 | - | 2 | V |
10 | Relative Intensity Noise+ | RIN | - | -150 | - | dB/Hz |
11 | Thermistor resistance | Rth | 9.5 | 10 | 10.5 | KΩ |
12 | TEC Current | Itec | - | - | 0.5 | A |
13 | TEC Voltage | Vtec | - | - | 5.0 | V |
* For ORI-MZM-T-20 and ORI-MZM-T-40 version, respectively.
+ Between 100MHz to 20GHz, with If=400 mA, -40dB reflection.
•Optical Characteristics*
No. | Parameter | Symbol | Min | Typ | Max | Unit |
1 | Output power (If=400mA) | OP | 12 | 13 | - | dBm |
2 | DC Extinction ratio | ER | 20 | - | - | dB |
3 | Wavelength range | λ | 1535 | 1550 | 1565 | nm |
4 | MPD1 responsivity+ | R | 0.01 | - | 0.5 | A/w |
5 | MPD2 Photocurrent (If=400mA) | Iph2 | 0.1 | - | - | mA |
* Tested at TEC 40°C.
+ PD responsivity is defined as max PD photocurrent over max output optical power, with fixed input.
Modulator function diagram
ORI-MZM-T-20* Typical S11 & S21 Curve
ORI-MZM-T-40* Typical S11 & S21 Curve
Absolute Maximum Ratings
ORI-MZM-T-BW
No. | Parameter | Symbol | Min | Max | Unit |
1 | Storage temperature | ST | -40 | 85 | °C |
2 | Operation temperature* | OT | -40 | 70 | °C |
3 | RF input power | EPin | - | 25 | dBm |
4 | Heater maximum power | HPin | - | 200 | mW |
5 | Maximum laser current | lop | - | 400 | mA |
* External temperature in oven.
